Appendix C – Event List Definition
Events | Definition |
Access Denied | User does not have access credentials |
Access Denied – Antipassback | User did not comply with antipassback conditions (did not log out) |
Access Denied – Card Blocked | Card credential blocked |
Access Denied – Card Expired | Card credential outside date of validity |
Access Denied – Card Not Programmed | Card credential not listed in the system |
Access Denied – Egress | Egress is disabled and will not allow access (outside time schedule) |
Access Denied – Reader Locked | Credential cant be used because the reader is locked |
Access Denied – Suspended | User credential is suspended |
Access Download Fail | Unable to synchronize credential information from ARCO |
Access Granted | User credential accepted |
Access Granted – Antipassback | User credential accepted and complies with antipassback conditions |
Access Granted – Duress | Duress is enabled (User in distress) |
Access Granted – Egress | Egress button has been pushed and access is allowed |
Access Not Taken | User did not enter the door |
Access Taken | User entered the door |
Activated | Used for indicating that an output is on |
Ajar | Door is open for an extended time |
Alarm | Alarm signal received |
Analog Alarm | Analog alarm signal received |
Analog Value | Value received is analog |
ARC Path 1 Failed | Connection to Alarm Reporting Center 1 has failed |
ARC Path 2 Failed | Connection to Alarm Reporting Center 2 has failed |
ARC Path 3 Failed | Connection to Alarm Reporting Center 3 has failed |
ARC-1 Offline | Alarm Reporting Center 1 is offline |
ARC-2 Offline | Alarm Reporting Center 2 is offline |
ARC-3 Offline | Alarm Reporting Center 3 is offline |
Arm Pending | Exit timer is running |
Armed | System is armed. Alarms will be reported |
Arming Failed | System arm failed |
Backup Communication Settings | Connection settings are for backup path |
Backup Connection | Connection to Arco is not the primary connection |
Battery Charger Failed | The battery charger is not functioning |
Battery Failed | The battery is not functioning |
Battery Fully Charged | Battery charge is at full capacity |
Battery Level | Battery charge level |
Battery Test Result | Battery status report |
Card Swiped | Card used on reader |
Configuration Defaulted | Configuration has be changed to default |
Configuration Download Fail | Configuration has failed to download |
Configuration Downloading | Configuration is downloading |
Configuration Updated Successfully | Profile configuration is updated in the controller OK |
CPU Temperature | Temperature of the control panel central processing unit |
CPU Temperature Fail | Temperature of the CPU exceeds normal (below 10°C or above +70°C) |
Custom 1 | Custom Role 1 |
Custom 1 Extend | Access time of Custom Role 1 is extended |
Custom 2 | Custom Role 2 |
Custom 2 Extend | Access time of Custom Role 2 is extended |
Device Substitution | A device has been tampered and replaced |
Disarmed | Area lock is disarmed |
Door Contact Trouble | Door contact input is in a trouble condition |
Duress | Duress is enabled (User in distress) |
Elapsed | |
Entry Timer Active | Entry timer for disarming an area is running. |
Ethernet Offline | Main ethernet connection is not connected |
Ethernet Offline (Expansion) | Expansion card ethernet is not connected |
Expired | Used to indicate a timer has expired |
External Temperature | Temperature around the enclosure |
External Temperature Fail | Temperature around the enclosure exceeds normal (below 10°C or above +70°C) |
Fault | Device has indicated a fault confition |
Firmware Available in Inactive Bank | Controller firmware is available in the secondary memory bank |
Firmware Download Failed | Firmware download unsuccessful |
Firmware Downloaded Successfully | Firmware download successful |
Firmware Downloading | Firmware is in the process of being downloaded |
Forced | Used to indicated that a door had been opened without a valid access |
Inhibited | Prevent alarm from sending a signal |
Input Changed (Test) | |
Invalid Login Attempt | User has attempted to enter a PIN that is not valid |
Isolated | Prevent alarms from sending external signals |
Latch | An input or device tamper/offline alarm has been latched on |
Late to Close | An area has not closed based on the programmed schedule |
Listening | Indicates a microphone is in a mode for listening to audio |
Locked | This is to indicate the state of a door preventing any access |
Logged In | User logged in |
Logged In – BLE | User logged in using ARCO Setup |
Muted | Indicates a microphone or speaker is disabled from working |
Offline | Device Offline |
Onboard Temperature | Temperature around the controller |
Onboard Temperature Fail | Temperature around the controller exceeds normal (below 10°C or above +70°C) |
Open | Indicates that a door is seen as being in the open state |
Partial Armed | Area mode whereby certain inputs can be masked for this mode. |
PIN Changed | PIN has been changed for a user |
Power Failed | Power supply is not functioning |
PSTN Line Offline | PSTN line is not connected |
Restarted | Controller has restarted |
Running | |
SD Card Failure | Failed to read from SD Card |
Sealed | State of an input when it is not in alarm |
Self Test Failed | The self-test of an input failed. |
Shutdown Pending | Controller battery level |
Signal Fail | GPRS Signal has failed. |
Signal Level | GPRS signal is OK and at level Good, OK, Poor |
Speaking | Speaker mode of the listen in is enabled for talkback |
Strike Trouble | Door strike contact monitor is in trouble state |
Suspect Latch | A device has had too many activations during the current mode |
Tamper | Alarm for interference on hardware enclosures |
Tamper (Masking) | |
Tamper (Open Circuit) | |
Tamper (Range Reduction) | |
Tamper (Short Circuit) | |
Test Mode | Test mode is activated |
Time Changed | Internal system time has been modified |
Too Many Invalid Logon Attempts | User has made too many login attempts |
Unknown Message | Message is not defined |
Unlocked | Door state is unlocked allowing access without presenting a card |
Unmasked Alarm | The raw state of an input |
User Count | Number of Users |
User Database 90%+ | User database capacity is more than 90% full |
Value | Analog input value |